Month: June 2015

Hypertech 32501 Max Energy Power Programmer for 2015 Corvette 6.2 LT1

David Ayers Leave a comment
Use This Post Clip for Email

Max Energy™…The Best Hand-Held Performance Tuner on the Market!

Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel, giving you more miles at part-throttle and more power at wide-open throttle. In order to increase engine efficiency, horsepower and torque, our engineers first optimize the spark and fuel curves point by point over the entire RPM band. With the additional power and optimized transmission functions, drivers use less fuel to accelerate and maintain cruising speeds without the torque converter unlocking or transmission down-shifting. The results are maximum power and fuel mileage.

  • Optimized engine tuning for premium octane (+34 Hp, +19 Tq)
  • Lower or raise the top-speed limiter to match the speed rating of factory-approved high-performance tires
  • Speedometer/odometer correction for tire sizes from 24″-30″ & rear gear ratios from 2.56:1-5.13:1
  • Disable 1-4 skip shift (Corvette w/manual transmission)
  • Adjust rev limiter +/- 500 RPM in 100 RPM increments
  • Read, display & clear DTCs
Hypertech 32501
Hypertech 32501

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Holley 350/500 CFM Street Avenger 2bbl Carburetors

David Ayers Leave a comment
Use This Post Clip for Email

Holley Introduces 350/500cfm Street Avenger 2bbl Carburetors

Street Avenger carburetors are known to bolt on right out of the box, and Holley is excited to announce the addition of itsnew 2bbl Street Avenger models, available in 350 and 500 CFM. Street Avenger carburetors have great features such as optimized street calibrations, three vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters, and an included 3/8” fuel line connection so there are no unnecessary trips back to the parts store.
Avenger carbs are the first to have a limited lifetime warranty. With a great warranty like that and the included comprehensive instruction manual, you can count on years of worry-free service.

  • Vibration polished for good looks
  • Optimized street calibration that works-out-of-the-box
  • Factory preset electric choke for easy startups (range identified and restricted for easy adjustments)
  • Built-in No Trouble fuel inlet filter
  • Street Avenger fuel metering system provides precise fuel control for great low-end torque and awesome acceleration
  • Ford A/T kick down (spring perch included)
  • Gen IV No Trouble power valve
  • Three vacuum ports (1 PCV/brake, 1 timed spark, 1 full)
  • Limited Lifetime Warranty – Guaranteed to be free from defects in material and workmanship for the life of the product!
  • 100% wet-flow tested by Holley technicians to ensure it arrives ready to run!

Applications:

0-80350: 350 CFM 2bbl Street Avenger (electric choke)

0-80500: 500 CFM 2bbl Street Avenger (electric choke)

 

Holley 0-80350
Holley 0-80350

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Hedman 68670

David Ayers Leave a comment
Use This Post Clip for Email

Hedman’s Standard-Duty, Uncoated Headers are manufactured using 18-gauge, mandrel-bent primary tubes (some models built using thicker 16- or 14-gauge tubing) and 1/4 flanges (some models use 3/8″ flanges).

The factory black paint applied to uncoated headers is not hi-temp, and is for pre-installation protection only. For the ultimate in protection against the elements, we suggest Hedman’s Original HTC coating.

All Hedman street hedders are MADE IN THE USA and are backed by a lifetime warranty against manufacturing defects!

 

Applications:

Chevrolet Camaro 1967-1987 (CID: 305, 350, 302, 400, 283, 327)

Chevrolet Nova 1969-1979 (CID: 305, 350, 302, 283, 400, 327)

Chevrolet Chevy II 1968 (CID: 327, 350, 302, 400, 283, 305)

 

Hedman 68670
Hedman 68670

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Centerforce KDF240916

David Ayers Leave a comment
Use This Post Clip for Email

NEW DUAL FRICTION CLUTCH KIT KDF240916

For 1962-1995 Chevrolet and GMC

Light Truck, SUV and Van

Centerforce provides top-of-the-line products for all performance levels using patented processes and thoroughly tested materials and designs to find the best combinations.

 

Features:

  • Centrifugal Weight System
  • Dual Friction Disc
  • Increased Holding Capacity
  • Light Pedal Effort

 

Kit Contents:

  • Pressure Plate
  • Disc
  • Throw Out Bearing
  • Alignment Tool
  • Pilot Bearing
  • Pressure Plate Bolts

 

Centerforce KDF240916
Centerforce KDF240916

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

B&M New Differential Covers for Chrysler, GM, and Chevy

David Ayers Leave a comment
Use This Post Clip for Email

The B&M Cast Aluminum Differential Cover was designed to strengthen the rear end by preventing case distortion, ring gear and cap bearing deflection. Constructed of A356.0-T6 aluminum, this rugged unit dissipates heat much faster than the stock factory unit to prolong the life of your ring and pinion gears. To increase durability and aesthetics without compromising heat dissipation, the cover has been coated with a U.S. military-grade (MIL-A-8625) black anodized finish. Additional features include an engraved B&M logo, added fluid capacity for better cooling, magnetic drain plug for catching ferrous metal particles, complete hardware, installation instructions and a one-year warranty.

 

New Part Numbers:

11306 – Differential Cover Chrysler 9.25″ Cast Aluminum

71501 – Differential Cover GM 10.5″ 14-Bolt Cast Aluminum

71505 – Differential Cover GM 9.5″ 14-Bolt Cast Aluminum

71504 – Differential Cover Chevy 8.875″ 12-Bolt Truck Cast Aluminum

B&M 11306
B&M 11306

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

AAM HONORS RALPH ACCINNO AT ANNUAL MEETING

David Ayers Leave a comment
Use This Post Clip for Email

Former Board Member Recognized for Invaluable Contributions

Thanking him for his years of service and support, Parts Pro parent company The AAM Group presented Ralph Accinno with a custom painting at a special dedication held during its recent Annual Membership Meeting. Accinno, retiring founder of Racer’s Equipment Warehouse in Rhode Island, provided many years of leadership on AAM’s Board of Directors and served as a tireless advocate for the group to affiliated vendors and other members.

AAM President Tim Odom commented, “We could not let Ralph leave AAM without a thank you. Among our members, Ralph was our most vocal supporter, and his endorsements always made a difference to AAM. He gave AAM meetings a unique character by way of his optimism, encouragement, infectious humor and even his occasional antics, which kept us on our toes. Fiercely loyal, Ralph set aside his own needs when the needs of the group or others were greater. I consider Ralph a personal friend, and I want to thank him personally for all he has done to mentor me in my role at AAM.”

L to R: John DeBalso (AAM Vice President of Purchasing and
L to R: John DeBalso (AAM Vice President of Purchasing and Vendor Relations), Ralph Accinno

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.