Category: Industry

K&N 63-2589 63 Series AirCharger Kit for 2015 Ford Mustang 2.3L

David Ayers Leave a comment
Use This Post Clip for Email

The K&N 63-2589 AirCharger air intake system replaces the restrictive factory air filter and air intake housing on some Ford Mustang models. K&N air intakes are designed to dramatically reduce air intake restriction as well as smooth and straighten air flow. This allows your engine to inhale a larger amount of air than the factory air filter assembly. More air means more usable power and acceleration throughout the engine’s RPM range. The 63-2589 air intake comes with a chrome-topped K&N high-flow air filter and a heat shield that installs into the original air box space. Air is directed through an aerodynamically engineered intake tube into the engine’s throttle body for guaranteed power gain. The tube accommodates the factory crank case vent hose and air inlet temperature sensor as well as the blow-off valve. The oversized cone-shaped air filter can be used for up to 100,000 miles before servicing is needed, depending on driving conditions. This air intake is relatively easy to install, usually in 90 minutes or less using your vehicle’s existing factory mounting points. The tools needed are a screwdriver, ratchet set and an Allen wrench. This air intake cannot be sold in California. It is not legal for use in California or other states adopting California emission standards.

  • Guaranteed horsepower gain
  • Designed to improve throttle response and engine sound
  • Free-flowing high density polyethylene tube
  • Replaces entire factory air intake system
  • Easy to install, usually in 90 minutes or less
  • K&N Million Mile Limited Warranty
K&N 63-2589
K&N 63-2589

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Hypertech 32501 Max Energy Power Programmer for 2015 Corvette 6.2 LT1

David Ayers Leave a comment
Use This Post Clip for Email

Max Energy™…The Best Hand-Held Performance Tuner on the Market!

Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel, giving you more miles at part-throttle and more power at wide-open throttle. In order to increase engine efficiency, horsepower and torque, our engineers first optimize the spark and fuel curves point by point over the entire RPM band. With the additional power and optimized transmission functions, drivers use less fuel to accelerate and maintain cruising speeds without the torque converter unlocking or transmission down-shifting. The results are maximum power and fuel mileage.

  • Optimized engine tuning for premium octane (+34 Hp, +19 Tq)
  • Lower or raise the top-speed limiter to match the speed rating of factory-approved high-performance tires
  • Speedometer/odometer correction for tire sizes from 24″-30″ & rear gear ratios from 2.56:1-5.13:1
  • Disable 1-4 skip shift (Corvette w/manual transmission)
  • Adjust rev limiter +/- 500 RPM in 100 RPM increments
  • Read, display & clear DTCs
Hypertech 32501
Hypertech 32501

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Holley 350/500 CFM Street Avenger 2bbl Carburetors

David Ayers Leave a comment
Use This Post Clip for Email

Holley Introduces 350/500cfm Street Avenger 2bbl Carburetors

Street Avenger carburetors are known to bolt on right out of the box, and Holley is excited to announce the addition of itsnew 2bbl Street Avenger models, available in 350 and 500 CFM. Street Avenger carburetors have great features such as optimized street calibrations, three vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters, and an included 3/8” fuel line connection so there are no unnecessary trips back to the parts store.
Avenger carbs are the first to have a limited lifetime warranty. With a great warranty like that and the included comprehensive instruction manual, you can count on years of worry-free service.

  • Vibration polished for good looks
  • Optimized street calibration that works-out-of-the-box
  • Factory preset electric choke for easy startups (range identified and restricted for easy adjustments)
  • Built-in No Trouble fuel inlet filter
  • Street Avenger fuel metering system provides precise fuel control for great low-end torque and awesome acceleration
  • Ford A/T kick down (spring perch included)
  • Gen IV No Trouble power valve
  • Three vacuum ports (1 PCV/brake, 1 timed spark, 1 full)
  • Limited Lifetime Warranty – Guaranteed to be free from defects in material and workmanship for the life of the product!
  • 100% wet-flow tested by Holley technicians to ensure it arrives ready to run!

Applications:

0-80350: 350 CFM 2bbl Street Avenger (electric choke)

0-80500: 500 CFM 2bbl Street Avenger (electric choke)

 

Holley 0-80350
Holley 0-80350

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Hedman 68670

David Ayers Leave a comment
Use This Post Clip for Email

Hedman’s Standard-Duty, Uncoated Headers are manufactured using 18-gauge, mandrel-bent primary tubes (some models built using thicker 16- or 14-gauge tubing) and 1/4 flanges (some models use 3/8″ flanges).

The factory black paint applied to uncoated headers is not hi-temp, and is for pre-installation protection only. For the ultimate in protection against the elements, we suggest Hedman’s Original HTC coating.

All Hedman street hedders are MADE IN THE USA and are backed by a lifetime warranty against manufacturing defects!

 

Applications:

Chevrolet Camaro 1967-1987 (CID: 305, 350, 302, 400, 283, 327)

Chevrolet Nova 1969-1979 (CID: 305, 350, 302, 283, 400, 327)

Chevrolet Chevy II 1968 (CID: 327, 350, 302, 400, 283, 305)

 

Hedman 68670
Hedman 68670

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Centerforce KDF240916

David Ayers Leave a comment
Use This Post Clip for Email

NEW DUAL FRICTION CLUTCH KIT KDF240916

For 1962-1995 Chevrolet and GMC

Light Truck, SUV and Van

Centerforce provides top-of-the-line products for all performance levels using patented processes and thoroughly tested materials and designs to find the best combinations.

 

Features:

  • Centrifugal Weight System
  • Dual Friction Disc
  • Increased Holding Capacity
  • Light Pedal Effort

 

Kit Contents:

  • Pressure Plate
  • Disc
  • Throw Out Bearing
  • Alignment Tool
  • Pilot Bearing
  • Pressure Plate Bolts

 

Centerforce KDF240916
Centerforce KDF240916

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

B&M New Differential Covers for Chrysler, GM, and Chevy

David Ayers Leave a comment
Use This Post Clip for Email

The B&M Cast Aluminum Differential Cover was designed to strengthen the rear end by preventing case distortion, ring gear and cap bearing deflection. Constructed of A356.0-T6 aluminum, this rugged unit dissipates heat much faster than the stock factory unit to prolong the life of your ring and pinion gears. To increase durability and aesthetics without compromising heat dissipation, the cover has been coated with a U.S. military-grade (MIL-A-8625) black anodized finish. Additional features include an engraved B&M logo, added fluid capacity for better cooling, magnetic drain plug for catching ferrous metal particles, complete hardware, installation instructions and a one-year warranty.

 

New Part Numbers:

11306 – Differential Cover Chrysler 9.25″ Cast Aluminum

71501 – Differential Cover GM 10.5″ 14-Bolt Cast Aluminum

71505 – Differential Cover GM 9.5″ 14-Bolt Cast Aluminum

71504 – Differential Cover Chevy 8.875″ 12-Bolt Truck Cast Aluminum

B&M 11306
B&M 11306

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

To Oil or Not to Oil: (That’s Not Really the Question)

David Ayers Leave a comment
Use This Post Clip for Email

By John M. Arnaud

Over the years, the air-filter experts at K&N have proven (in their in-house filtration test lab, no less) that the secret to increasing airflow to your engine without sacrificing protection lies in their exclusive air filter oil. This oil, which permeates a filter’s cotton fibers, grabs dust and other microscopic contaminants and keeps them from entering your system. Non-oiled paper filters don’t even come close.

So the question isn’t whether you should be using an oiled filter (you should); instead, you should be asking “How much should I use?” and “How do I apply it?” The answers to those questions depend on which delivery system you use: squeeze bottle or aerosol applicator. Read on for the scoop from K&N:

Squeeze Bottle

Apply the air filter oil evenly along the crown of each pleat, then allow the oil to wick for 20 minutes before touching up any light areas on either side of the filter.

K&N Squeeze Oil
K&N Squeeze Oil

Aerosol Bottle

Spray the oil evenly along the crown of each pleat, holding the spray nozzle about 3” away from the filter. Allow the oil to wick for 20 minutes, then touch up any light areas on either side of the filter.

K&N Aerosol Oil
K&N Aerosol Oil

Most K&N air filters are oiled at the factory, so reoiling shouldn’t be necessary until it’s time to clean your filter, usually at 50,000 or 100,000 miles, depending on your application. K&N’s Recharger kits contain everything you need to freshen up your filter, including filter cleaner and your choice of oil dispenser.

Head on over to your local Parts Pro retailer to pick up a K&N Recharger kit, or find a local affiliated store using our dealer locator.

If you are a performance aftermarket accessory retailer who would like to become part of the nationwide Parts Pro network, please join us today!

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Small Business Week Salutes Big Dreams

David Ayers Leave a comment
Use This Post Clip for Email

by John M. Arnaud

 

National Small Business Week starts next week (May 4–8), and Parts Pro wants to make sure our local retailers get all the credit they deserve.

Since the early 60s, Small Business Week has recognized this nation’s independent businesses, which generate two out of every three new jobs in this country and help to power our economy from coast to coast. Beyond the numbers, however, small businesses represent a core American truth: the prosperity available to those willing to follow their passions through hard work and determination.

Though Small Business Week is a time to soak in the kudos, it’s also a terrific opportunity to engage your customers and promote your business throughout your local area. Here are some ways you can do just that:

  • Participate in any activities sponsored by your local Chamber of Commerce.
  • Talk up Small Business Week and the importance of supporting local businesses with your customers via social media (Facebook, Twitter, etc.).
  • Extend special discounts or promotions to your customers to thank them for their support.
  • Announce and host an open house in your store to celebrate the occasion. (Email is a great way to communicate a last-minute event!)
  • Partner with a local performance or automotive club to share your expertise on a particular subject or host a workshop. For example, you might demonstrate how to perform an installation or talk about exciting new products.

Parts Pro would like to congratulate all of our entrepreneurs who have demonstrated the courage, grit, and determination required to pursue their dreams and help us grow the industry we all love.

Performance junkies: Head in to your local automotive accessories retailer next week to share your support and appreciation. Or find one using our dealer locator.

Performance retailers: If you would like to become part of the nationwide Parts Pro network, please join us today!

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

Hooker Headers’ Blackheart Exhaust Systems Hit the Street

David Ayers 1 Comment
Use This Post Clip for Email

by John M. Arnaud

Attention 2015 Ford Mustang GT owners: it’s time to get your growl on!

Hooker Headers has announced its Blackheart catback and axleback exhaust systems for GTs equipped with the 5.0L Coyote V8. These exhaust systems, which are available both with and without mufflers, offer the aggressive sound and dyno gains you need to leave your mark on the street.

Hooker Headers Blackheart Exhaust
Hooker Headers Blackheart Exhaust

Fabricated from 18-gauge 304 stainless steel, these Blackheart exhaust systems are primed for strength and long life. A straight-through muffler design and 3” diameter exhaust free up your flow for unobstructed performance. Exclusive tube geometry allows maximum ground clearance, and a design that uses existing mounting points facilitates a headache-free installation.

Hookers’ Blackheart exhaust systems look as good as they sound, with 4” dual-wall, polished stainless steel tips laser-etched for that final layer of detail.

The Blackheart benefits from Hooker Headers’ limited lifetime warranty to the original purchaser, which guarantees the product to be free from defects in material and workmanship for the life of the product on the original car on which it is installed.

Head on over to your local Parts Pro retailer to grab one for yourself, or find a local store using our dealer locator.

If you are a performance aftermarket accessory retailer who would like to become part of the nationwide Parts Pro network, please join us today!

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.

MSD Completes Mallory Merger

David Ayers Leave a comment
Use This Post Clip for Email

mallory-msd-merger

One good M deserves another.

Following the January 2015 acquisition of ACCEL Performance Group (maker of Mallory Ignition, Mr. Gasket, Hays, QuickTime, and others) by MSD Performance, the MSDP Group completed the planned merger of the Mallory and MSD lines to create the top ignition company in the automotive aftermarket.

As of March 31, the Mallory product line will no longer be produced; all Mallory products will be manufactured exclusively under the MSD brand. MSD will, however, continue to produce and service Mallory distributor replacement parts such as points, rotors, caps, and more than one hundred other items. In addition, MSD will continue repairing Mallory products and honoring all original Mallory warranties. Retailers, installers, and customers should direct Mallory warranty inquiries to MSD’s toll-free number: (800) 246-0270.

Mallory and MSD together bring more than a century of ignition innovation and expertise. The MSDP Group remains committed to leveraging the two brands’ combined resources to keep igniting their loyal customers.

Your Parts Pro retailer will be happy to help you find your favorite ignition part. Find your closest affiliated store using our dealer locator.

If you are a performance aftermarket retailer who would like to become part of the nationwide Parts Pro network, please join us today!

Ready to buy? Need help with the install? To find your nearest Parts Pro affiliate, see our Store Locator. Or join the conversation at the Parts Pro Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of manufacturers with whom it has a business relationship.